Rockford Fosgate Power 800.2 2-Channel Car Amp

Rockford Fosgate Power 800.2 2-Channel Car Amp

Rockford Fosgate Power 800.2 2-Channel Car Amp

Rockford Fosgate Power 800.2 2-Channel Car Amp

Rockford Fosgate Power 800.2 2-Channel Car Amp

Rockford Fosgate Power 800.2 2-Channel Car Amp

Rockford Fosgate Power 800.2 2-Channel Car Amp

Rockford Fosgate Power 800.2 2-Channel Car Amp

Rockford Fosgate Power 800.2 2-Channel Car Amp

Old school Rockford Fosgate Power 800.2 amplifier! Used but in real good condition. Clean and fully functional, everything tested and working properly. This is old school Rockford at its best. Don’t underestimate their power series, this was especially underrated and can really impress! I’ll provide some specs below for it as they are hard to find on a model this old. If you’d like to make an offer you can message me. Be aware that I also have this listed locally and may pull the listing if someone buys it locally. Bridged Into A 4-Ohm Load: 960 watts x 1. Per Channel Into A 2-Ohm Load: 480 watts x 2. Per Channel Into A 4-Ohm Load: 240 watts x 2. Bridged Into A 4-Ohm Load: 800 watts x 1. Per Channel Into A 2-Ohm Load: 400 watts x 2. Per Channel Into A 4-Ohm Load:200 watts x 2. TRANSana (TRANSconductance Active Nodal Amplifier): The TRANSana is a circuit that allows the audio signal to pass through the amplifier at low voltage. The signal is directly level-shifted to the fixed high voltage rails via a pair of drive transistors. Signal linearity is assured by an active node formed by the drive transistors at ultrasonic frequencies. The result is crystal clear sound quality. Cast Aluminum Heatsink: The cast aluminum heatsink dissipates heat generated by the amplifier’s circuitry. The inherent advantage of casting provides a 30% improvement of cooling over conventional extrusion heatsink designs. MEHSA (Maximum Efficiency Heat Sink Application): MEHSA is a Rockford Fosgate proprietary process that increases the heat transfer from the MOSFET devices to the heatsink. The multi-layer insulated metal MEHSA substrate operates with minimal thermal resistance, spreading heat both downward and outward to quickly dissipate heat from each device across the heatsink. This allows greater power output, enhanced thermal stability, and maximum reliability. TOPAZ (Tracking Operation Pre-Amplifier Zone): TOPAZ is a circuit that simply eliminates noise. The TOPAZ circuit allows the amplifier ground to move with the source unit ground, creating a “noise elimination” zone just before the preamp section. If there is any noise in the ground coming down the RCA line to the amplifier, TOPAZ amazingly tracks it down and eliminates it. The result is a 30-40dB improvement of the isolation between input ground and chassis ground. NOMAD (NOn-Multiplying Advanced Decision): NOMAD is an intelligent protection circuit that uses an analog computer to make real time decisions regarding temperature, voltage, current and impedance. The unit is protected without limiting sound output unless needed. DSM (Discrete Surface Mount): In the manufacturing process high speed robotics are used to place 0% tolerance resistors and large board traces providing greater reliability and efficiency. Internal Crossover: The internal crossover is a 24dB/octave Butterworth filter selectable for high-pass, full range, or low-pass operation variable from 50Hz to 210Hz. Remote Punch Bass: The Punch Bass helps correct for acoustical deficiencies in the listening environment by helping reproduce full range sound without adding excessive boost. The Punch Bass control has a narrow band adjustment centered at 45Hz, variable from 0dB to +18dB. Using the mounting bracket, the supplied Punch Bass wired remote can be mounted in any convenient location under your vehicle’s dash. The wired remote is 2.317″ wide, 1.523″ tall and 2.035 deep. RCA Pass-Thru Jacks: The pass-thru jacks provide a convenient source for daisy-chaining an additional amplifier without running an extra set of RCA cables from the front of the vehicle to the amplifier location. The pass-thru jacks output a full signal. RF Center Badge: For installation flexibility, the RF center badge can be rotated 180 degrees. Left Side Of Amplifier. Crossover Switch: Allows you to select high-pass, full range, or low-pass crossover operation. Crossover Frequency: The crossover frequency control is variable from 50Hz to 210Hz. Left Gain: This variable gain control allows you to adjust the output level of the left channel. Right Gain: This variable gain control allows you to adjust the output level of the right channel. Input: Gold-plated RCA jacks. Pass-Thru: Gold-plated RCA jacks. Speakers: Gold-plated set screw terminals that will accept up to 8 gauge speaker wire. Remote Punch Bass: RJ-45 jack for use with supplied Remote Punch Bass wired remote. Right Side Of Amplifier. GND: Gold-plated set screw terminal that will accept up to 4 gauge ground wire. B+: Gold-plated set screw terminal that will accept up to 4 gauge power wire. REM: Gold-plated 0.250 quick-slide for remote turn-on lead. Note: A female quick-slide is not supplied. The item “Rockford Fosgate Power 800.2 2-Channel Car Amp” is in sale since Friday, September 08, 2017. This item is in the category “Consumer Electronics\Vehicle Electronics & GPS\Car Audio\Car Amplifiers”. The seller is “989zach” and is located in Midland, Michigan. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, Sweden, South Korea, Indonesia, Taiwan, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Russian federation, Israel, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia.
  • Brand: Rockford Fosgate
  • Model: Power
  • Channels: 2
  • RMS Power: 800W

Comments

Comments are closed.