Rockford Fosgate P3D2-12 Pair of Punch P3 12 subwoofers & T1000-1bdCP Power Amp

Rockford Fosgate P3D2-12 Punch P3 12 subwoofer with dual 2-ohm voice coils (PAIR) and Rockford Fosgate T1000-1bdCP Power Series mono sub amplifier 1,000 watts RMS x 1 at 2 ohms and a SOTS Lanyard. Punch P3 Pair of 12 subwoofer with dual 2-ohm voice coils and Rockford Fosgate T1000-1bdCP Power Series mono sub amplifier 1,000 watts RMS x 1 at 2 ohms. Pair of Rockford Fosgate P3D2-12. Two Punch P3 12 subwoofer with dual 2-ohm voice coils. 12 subwoofer with dual 2-ohm voice coils. Anodized aluminum cone with Santoprene surround. Hybrid StampCast basket provides strength while minimizing weight and resonance. Vertical Attach Surround Technique (VAST) increases cone area. Power range: 300-600 watts RMS (1200 watts peak power). Frequency response: 27-250 Hz. 75-1.25 cubic feet. Ported box volume: 1.79 cubic feet. 1 ohm or 4 ohms. Ideal Sealed Box Volume (cubic feet). Ideal Ported Box Volume (cubic feet). 85 dB at 1 watt. 27 – 250 Hz. RMS Power Range (Watts). Top Mount Depth (inches). Bottom Mount Depth (inches). Cutout Diameter or Length (inches). Overview: The Rockford Fosgate Punch P3D2-12 is a 12-inch subwoofer with dual 2 voice coils. The sub features a hybrid StampCast basket, quick-release compression terminals, anodized aluminum cone, and Santoprene surround. An anodized aluminum voice coil former and spider venting help keep the subwoofer cool. Dual 2 Voice Coils: The dual 2 voice coils offer wiring flexibility; when wired in parallel the woofer presents a 1 load, when wired in series the woofer presents a 4 load. Compression Terminals: The P3D2-12 features spring post terminals which accommodate speaker wire up to 10 gauge. FlexFit Basket: The Flex Fit frame utilizes slots (where possible) instead of single screw sized holes; allowing slight adjustment of the speaker when mounted. Trim Ring: To improve the cosmetic look, a decorative trim ring is included that mounts over the flange of the woofer. When using the cast aluminum trim ring the woofer is first mounted with four screws, then the ring is placed on top of the woofer, aligning the final four holes of the woofer with ring. The other four screws are used for these holes to mount the ring and woofer to the enclosure. Without the trim ring the mounting height of the woofer is just under 7/8 of an inch, with the trim ring it’s approximately 1-1/16 inches. The diameter of the trim ring is 13-5/16 inches. Sealed Box: Rockford recommends a sealed enclosure with an optimum internal volume of 1.02 cubic feet (from 0.75 to 1.25 cubic feet is acceptable). Sealed enclosures provide the most control over a woofer, will handle a lot of power, and provide accurate sonic reproduction, making them suitable to all types of music. Ported Box: Rockford recommends a ported enclosure with an internal volume of 1.79 cubic feet using one 4″ diameter x 10″ long port; this yields a tuning frequency of 40 Hz. Ported (or vented) enclosures typically provide better overall efficiency than sealed so they are suitable for use with smaller amplifiers, giving you more bass output from less power. However, this efficiency comes at the expense of very low frequency output (below 33 Hz). Power Series mono sub amplifier 1,000 watts RMS x 1 at 2 ohms. 700 watts RMS x 1 at 4 ohms (1,000 watts RMS x 1 at 2 ohms). 1,000 watts RMS x 1 at 1 ohm. Dynamic Thermal Management cooling system. Variable low-pass filter (35-250 Hz, 24 dB/octave). Selectable subsonic filter (28Hz, 24 dB/octave). Variable bass boost (0-18 dB at 45 Hz). Optional wired remote bass boost. MOSFET power and output stages. 4-gauge power and ground leads and an 150-amp fuse recommended wiring and hardware not included with amplifier. No onboard fuses when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended. 13-11/16″W x 2-1/4″H x 8-15/16D. RMS Power Output (Watts x Channels). Peak Power Output (Watts x Channels). Power at 2 Ohms (Watts x Channels). Bridged Power (Watts x Channels). THD at Rated RMS Power. Signal to Noise Ratio. Overview: With its super efficient Class-BD circuit topology and Constant Power configuration, the Rockford Fosgate Power T1000-1bdCP assures maximum power output. Due to its dedicated low frequency response, this amplifier is optimized for mid-bass speakers or subwoofers only. The amplifier is 1-ohm stable (1,000 watts x 1) and will drive a pair of 4-ohm DVC subwoofers or quad-configuration of 2-ohm DVC subwoofers with ease. Class bd Design: Rockford Fosgate bd topology is a revolutionary patented design, integrating a technology that is more efficient than typical class AB and has lower distortion than class D designs. Power bd amplifiers are 75-80% efficient vs. 20-60% efficient class ab amplifiers. This means, more power from your amplifier with less drain on your vehicles electrical and charging system. Constant Power: Its proprietary “Constant Power” configuration provides the ability to instantaneously deliver maximum output power to speakers without regard to its varying impedance while maintaining high-efficiency and thermal performance. Music and speakers have a dynamic relationship. So your listening experience is cleaner, louder and more impressive than ever before. Cast Aluminum Heatsink: The cast aluminum heatsink dissipates heat generated by the amplifier’s circuitry. The inherent advantage of casting provides a 30% improvement of cooling over conventional extrusion heatsink designs. Dynamic Thermal Management (DTM): DTM Evenly distributes excess heat across entire amplifier heatsink. DSM (Discrete Surface Mount): DSM utilize 1% tight-tolerances improving efficiency of the circuit, decreases cross-talk from other discrete components and lowers operating temperature. An industry-leading manufacturing process, DSM utilizes high-speed robotics, high-quality 1% tight-tolerance parts and large board traces. The discrete components are laser etched to meet a particular value and a very low tolerance. This lower tolerance improves the efficiency of the circuit, decreases cross-talk from other discrete components and lowers operating temperature. TO-247 MOSFETs: The Rockford Fosgate amplifier use custom TO-247 MOSFETs. These have 60% more metal tab area for more power capacity, lower impedance and improved heat dissipation over traditional TO-220 MOSFETs found in many other amplifier. The MOSFET transistor is the best type of device to use when building a high quality mobile amplifier. The TO-247 has 60% more metal tab area and its unique, fully encapsulated design is capable of housing a silicon die (the heart of the MOSFET) twice as large as the TO-220. Additionally, the extra metal tab area ensures that no matter what size silicon die is inside, the thermal impedance will always be lower than in the TO-220 due to improved heat dissipation. MEHSA3: MEHSA3 reduces MOSFET temperatures, lowers distortion, increases durability and prolongs the output device life span. MEHSA3 Maximum Efficiency Heat Sink Application – gen. 3 is a proprietary process that yields up to five times better heat transfer than traditional FET mounting techniques, using the exact same components. A multi-layer insulated metal substrate operating with minimal thermal resistance spreads heat both downward and outward to quickly dissipate heat from each device across the heatsink. This process combined with Rockford’s optimized heatsink designs, DSM (Discrete Surface Mount) technology and MOSFET devices, allows the amplifier to squeeze more watts per cubic inch from every output device as well as provide consistent thermal stability. The 3rd generation creates a dielectric layer between the ceramic topside and the aluminum base that retains all of the electrical isolation and capacitive coupling of the original MEHSA material increasing it’s thermal conductivity. NOMAD (NOn-Multiplying Advanced Decision): NOMAD is an intelligent protection circuit that uses an analog computer to make real time decisions regarding temperature, voltage, current and impedance. The unit is protected without limiting sound output unless needed. Power and Protection LEDs: The LEDs are located on top of the amplifier. A blue Power LED illuminates when the amplifier is turned on. A red Thermal LED illuminates if the amplifier overheats. The yellow Protect LED illuminates if a short circuit or too low an impedance is detected at the speaker connections. When any of the protection circuits engage, the amp automatically shuts down until the problem is corrected. Internal Crossover: The amplifier features a built-in 24dB/octave Butterworth low-pass filter with a variable crossover point from 35Hz to 250Hz. Punch EQ2: The Punch EQ on-board equalization circuit helps correct for acoustical deficiencies in the listening environment. This control is a narrow band adjustment variable from 0dB to +18dB at 45Hz with a Gyrator based Punch EQ that eliminates frequency shift with boost. Infrasonic Filter: This 28Hz high-pass filter (12dB/octave Butterworth) is designed to prevent frequencies below the audio range from being applied to the subwoofer from the amplifier. Power Connections: The power and ground terminals are nickel-plated captive c-clamp wire connectors and will accommodate up to 4-gauge wire. An external 150-amp fuse (not included) must be installed on the power wire. If a wiring kit is used which includes a fuse with a value other than 150-amps, the original should be replaced with a 150-amp fuse. The remote turn-on terminal will accept wire sizes of 12- to 24-gauge. A Phillips-head or slotted screwdriver (not supplied) is required to tighten/loosen the terminals. Dual Speaker Terminals: The Power mono-amplifier features two pair of speaker output terminals so you can easily connect two 4-ohm speakers to the amplifier in a 2-ohm load configuration. The two pair of nickel-plated clamp wire connectors will accept 8-gauge to 18-gauge wire. Differential Input RCA Inputs: The amplifier features a pair of differential RCA input jacks for easy connection of signal level input. Differential input circuitry measures the voltage of both the positive (+) and negative (-) portions of the input signal, subtracting the voltage common to both conductors (noise); resulting in a cleaner signal. Reducing the noise on the input then improves the sound quality of the output. The RCA input jacks are nickel-plated to resist signal degradation caused by corrosion. RCA Outputs: The amplifier also features a pair of RCA “Pass-Thru” jacks which provide a convenient source for daisy-chaining an additional amplifier without running an extra set of RCA cables from the front of the vehicle to the rear amplifier location. The RCA output jacks are nickel-plated to resist signal degradation caused by corrosion. NOTE: Any return that does not have a return authorization number written on the outside of the package will not be accepted. Sound of Tri-State has the sole discretion as to what is warrantied. It is our intention to keep you, the customer happy. After 14 days from your receipt date, defective items may be repaired or replaced at Sound of Tri-State’s discretion Except Remanufactured products, which are only repaired. We have trained technicians on staff and ready to help with you with any questions. We are open Monday to Friday from 10 a. EST (Eastern Standard Time). The item “Rockford Fosgate P3D2-12 Pair of Punch P3 12 subwoofers & T1000-1bdCP Power Amp” is in sale since Wednesday, December 13, 2017. This item is in the category “Consumer Electronics\Vehicle Electronics & GPS\Car Audio\Car Subwoofers”. The seller is “soundoftristate” and is located in Claymont, Delaware. This item can be shipped to United States, Canada.
  • Brand: Rockford Fosgate
  • MPN: P3D2-12_PKG
  • Speaker Size: 12″
  • Model: P3D2-12+T10001BDCP
  • Voice Coil: Dual

Incoming search terms:

  • rockford fosgate 4080 dsm
(2) Rockford Fosgate Punch P3D2-12 12 Subs+Vented Box+1500W Amplifier+Amp Kit

(2) Rockford Fosgate Punch P3D2-12 12 Subs+Vented Box+1500W Amplifier+Amp Kit

(2) Rockford Fosgate Punch P3D2-12 12 Subs+Vented Box+1500W Amplifier+Amp Kit

(2) Rockford Fosgate Punch P3D2-12 12 Subs+Vented Box+1500W Amplifier+Amp Kit

(2) Rockford Fosgate Punch P3D2-12 12 Subs+Vented Box+1500W Amplifier+Amp Kit

(2) Rockford Fosgate Punch P3D2-12 12 Subs+Vented Box+1500W Amplifier+Amp Kit

(2) Rockford Fosgate Punch P3D2-12 12 Subs+Vented Box+1500W Amplifier+Amp Kit

(2) Rockford Fosgate Punch P3D2-12 12 Subs+Vented Box+1500W Amplifier+Amp Kit

(2) Rockford Fosgate Punch P3D2-12 12 Subs+Vented Box+1500W Amplifier+Amp Kit

(2) Rockford Fosgate Punch P3D2-12 12 Subs+Vented Box+1500W Amplifier+Amp Kit

Car Audio & Video. Package: (2) Rockford Fosgate Punch P3D2-12 12 Dual 2 Ohm Car Subwoofers Totaling 2400 Watt Peak / 1200 Watt RMS + Rockville dB15 6000 Watt Peak 3000 Watt RMS Mono Class D Car Amplifier + Rockville RWK0CU 0 Gauge 100% Pure OFC Copper 2 Channel Complete Wire Kit With RCA Cables + Rockville RDVB12 Dual 12 1.75 cu. Ft Vented/Ported Subwoofer Enclosure + Dual Enclosure Wire Kit With 14 Gauge Speaker Wire + Screws + Spade Terminals. Condition: BRAND NEW IN ORIGINAL PACKAGING. (2) Rockford Fosgate Punch 12 Car Subwoofers. (1) Rockville Dual 12 1.75 cu. MDF Vented/Ported Sub Enclosure Box. (1) Rockville dB15 6000 Watt/3000w RMS Mono Class D 2 Ohm Car Audio Amplifier. (1) Rockville RWK0CU 0 AWG Gauge Complete Amp Installation Wire Kit. 20 Drywall Wood Screws (Wood screws are the type of screws; the screws are actually made of metal). 20 Feet of 14 AWG Blue Speaker Wire. Features of Rockford Fosgate Subs. Rockford Fosgate Punch P3D2-12 12 1200 Watt. Peak Power: 1200 Watts. RMS Power: 600 Watts. Nominal Impedance: Dual 2-Ohm. Anodized aluminum cone and dustcap. Custom 10-AWG nickel plated push terminals. Diamond cut cast aluminum trim ring. Dual linear spider with embedded 16 AWG tinsel leads. Extended pole piece and bumped vented backplate. High-temp voice coil with spun-laced Nomex® re-inforcement collar. Protective PVC textured magnet cover. StampCast basket with integrated spider venting. Cutout Diameter: 11.25 inches / (285 mm). Mounting Depth: 6.66 inches / (169.3 mm). Voice Coil Diameter: 2.5 / (65.5 mm). Magnet Weight 96 oz / 2.73 kg. Speaker Connector: Dual 10 AWG compression. Woofer Displacement: 0.194 cu. Ft / (5.5 Liters). Fs (Hz): 26.5. Re (Ohms): 3.20. Le (mH): 4.25. Vas (Liters): 57.7. Xmax (mm): 15.2. Vb: 1.02 cu. F3: 43.4 Hz. Speaker Cutout: 11.25 inches. Speaker Depth: 6.66 inches. Vd: 0.194 cu. Vb: 1.79 cu. F3: 33.2 Hz. Dp: 4 inches diameter. Lp: 10 inches long. Vp: 0.073 cu. Recommended Enclosure Type: ported or sealed. Minimum Sealed Box Volume: 0.50 cubic feet. Optimum Sealed Box Volume: 0.75 cubic feet. Maximum Sealed Box Volume: 0.85 cubic feet. Minimum Ported Box Volume: 0.70 cubic feet. Top-Mount Depth: 4.57. Cutout Diameter: 9.13. The dB15 is a class D monoblock high power amplifier with 6,000 watts peak output, 3,000 watts RMS output, and 1500 watts CEA-2006 rated power. All of the mono amplifiers in the dB series are 2 ohm stable. They are all CEA-2006 compliant, which makes it easy to compare this amplifier to other CEA compliant amps on the market. Here at Rockville we offer the best value in car audio. We therefore want to make it easy for you to compare our products to any brands on the market. So we provided 3 ratings for all of our car amplifiers. This peak power is the amount of power the amp puts out at the loudest moments during a particular song. This formula almost always works within 20 %. This amp has a fully adjustable 12dB/Octave crossover with differential circuitry. Other features include a subsonic filter, a fully adjustable bass equalizer, mute and delay soft start technology, a phase control switch, and a dashboard subwoofer control for added convenience. The dB15 is protected by a full IC controlled circuit and has professional peak limiter circuitry guaranteeing distortion free music playback at all levels. The RCA input accepts both balanced and un-balanced inputs. If there is potential inference in the car, the balanced input signal is less susceptible to noise. The dB amps by Rockville use the top parts and components recommended by Rockville’s very own engineer. These amps are the best sounding out of any series we have ever created. They perform more efficiently resulting in even dB of sound. We created them to be 2 ohm stable just like the world’s most famous amps by Rockford Fosgate, Kicker, etc. If you compare our amp to the most famous amps you will find our amp can compete and, in my opinion, surpass the performance of anything in its class. Each and every amplifier we manufacture is tested twice. Once at the semi-finished PCB stage of production, and then another test is done at the final assembly. We also run age tests on them. After this is all done, we hire a 3rd party independent company unaffiliated with our factory or with us to go to the factory and inspect 20% of all the production items. We test the power, the controls, and over 20 other tests. We guarantee these amps will satisfy you. (Amp must be complete along with the box). Birth sheet with tested power. Rockville dB156000 Watt/3000 Watt RMS Mono Class D 2 Ohm Car Stereo Amplifier With Optical Coupler Technology. CEA Compliant Power Ratings (Rated at less than 1 % distortion) Use these CEA ratings when matching and comparing with other CEA compliant brands such as Kicker, Rockford Fosgate, etc. O 2 Ohm: 1500 Watts x 1 Channel <1% THD+N o 4 Ohm: 900 Watts x 1 Channel <1% THD+N. RMS Power Ratings: Use these RMS ratings when comparing with great brands such as Hifonics, Earthquake, Soundstream, etc. O 2 Ohm: 3000 Watts x 1 Channel o 4 Ohm: 1800 Watts x 1 Channel. Peak: The amount of power the amplifier can produce for a split second at the loudest part of a song o 2 Ohm: 6000 Watts x 1 Channel o 4 Ohm: 3600 Watts x 1 Channel. High-Speed MOSFET Power Supply. Optical Coupler Class "D" Technology. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Low Pass Filter: 50Hz - 250Hz. Subsonic Filter: 15Hz - 55Hz. Full IC-Controlled Protection Circuitry. Remote Dashboard Subwoofer Control. Fully Adjustable 12dB Bass Equalizer. Mute and Delay Soft Start System. RCA Preamp Line Output. 8 Volt Preamp Circuitry. Status Mode LED Indicator. Minimum THD at Rated Power: <0.1%. S / N Ratio: >90dB. Under Voltage Protection at 10V. Over Voltage Protection at 16V. Frequency Response: 15Hz – 250Hz. 150 Amp Maxi Fuse. Dimensions: (W x H x L)9? About Rockville Quality Control Procedures. The Rockville brand stands for Quality, Innovation and Value. We aim to deliver products twice as good as our competitors at a fraction of the cost of famous brands. All Rockville products go through the most rigorous quality control standards in the industry. Products go through months of extensive testing before they reach your hands. All functions and components are tested for quality. Rockville makes products that are virtually un-breakable! Rockville is one of the only brands in its class to have engineers and technicians test every concept model for weeks or months before starting production. Once production begins, Rockville sends product engineers to the factory to quality control every product. After production is complete Rockville has the head of QC in our overseas office test a certain percentage of all products from the production line a second time to ensure that the quality meets our strict standards. We challenge anyone to put this wire to a resistance test against any other wire on the market with the same gauge. Why are we so confident? This cable is 100% copper. You cant have a cable with more copper than 100 %. So the only way a cable would out-perform this one is if it were being advertised as a 0 AWG but they are giving you more wire than advertised. We guarantee that this kit will compete with the most expensive amp kits on the market from Kicker, JL Audio, or any other top brands. Looking for a wire kit that has 100% true specifications? A wire kit that uses 100% copper 0 gauge cable? Then look no further than the Rockville True-Spec RWK0-CU 0 Gauge Amplifier Wiring Installation Kit. This package includes everything you’ll need to get your amplifier system powered-up correctly and at peak efficiency. The power and ground cables aptly named “Mega Power Cable” are a no compromise power cable. Rockville’s engineering team over-built and designed the cables using thousands of strands of only true 100% oxygen-free, silver-tinned copper strands. The use of a proprietary special twisting process reduces “surface skin impedance loss” so that Mega Power cables have zero signal and power loss, delivering full power from your battery system to your amplifier even at lengths of 20 feet! The increased current flow and higher amperage carrying capacity will increase your amplifiers efficiency and keep your amplifier running cooler. The SuperFlex outer insulating jacket jacket makes installation and cable routing simple and easy. The 100% copper stranded wire is extremely tolerant of the hostile conditions found under the hood in vehicles and compensates for vibration, heat expansion and flexibility. This flexible and well shielded wire is crucial for getting through all of the nooks and passageways within the confines of a vehicle interior. Some manufactures use all aluminum or mix a little copper with aluminum to give their cables the appearance of a “heavy-duty” cable. But not Rockville, our True-Spec 100% oxygen free, silver tinned copper eliminates corrosion, increases current transfer x 10, and won’t discolor over time. The superior quality and materials of the Rockville 100% True-Spec amplifier installation kit is realized in the included accessories and cable workmanship. Included is a precision CNC cut full size ANL fuse housing, machined from solid brass and then 14K gold plated for superior signal transfer and complete with a matching gold plated 250-amp ANL fuse. The power cable is wrapped in 6 feet of durable nylon braided tubing to protect it from heat and chafing in the engine compartment. All installation accessories such as the ring terminals and spade connectors are nickel plated for superior signal transfer and durability. CRYSTAL SQ AUDIO PLANAR SPEAKER CABLE The speaker cable included in the Rockville True-Spec is also manufactured from 100% copper and woven in to a flat planner design and coated in our Super-Flex insulation so that it fits under and around your vehicles trim and carpet smoothly and without bulking up. With crystal clear sound quality these speaker cables deliver true audio fidelity from your car audio amplifier to your speakers. The 12 gauge speaker cable included in the 0 gauge kit can handle over 3000 watts of power without heating up or degrading signal quality. CRYSTAL SQ RCA AUDIO INTERCONNECT CABLE Designed and engineered to be the best sounding, best performing and best looking RCA cables available today. Each channel in the RCA cable is triple shielded first with dielectric internal insulators and then with a 98% coverage woven shield. All cables are manufactured of 100% oxygen free copper and feature twisted pair technology for superior noise rejection and pure sonic signal flow. The RCA plugs are shielded metal and feature a spiral cut outer ground ring with center split pin for precise and tight audio connections. The result of all this technology is noise free-noise rejection signal transfer for optimum sound quality. You will hear the difference these RCA signal transfer cables will make. Amplifier Kit Key Features. 0 Gauge Power Amplifier Installation Kit. Designed specifically for car audio systems over 1000 watts RMS to 3000 Watts. Made from silver-tinned 100% virgin copper for a pure uninterrupted transfer of power and signal. The solid brass gold plated ANL Fuse Holder offers ideal protection for high powered systems. Frosted Blue 0 gauge power wire with seamless crimp ring terminal. Frosted Gray 0 gauge ground wire. Blue 18 gauge remote lead wire. Frosted Clear/Blue 12 gauge flat speaker wire. Triple shielded twisted pair RCA cables. One ANL Fuse Holder with 250 amp ANL fuse. One 1/2 black rubber firewall grommet. Two 0 gauge spade terminals. Two black 12 gauge nickel-plated spade lugs. Three blue 12 gauge nickel-plated spade lugs. One black 0 gauge ring terminal. Ten 6 black zip ties. Description for Rockville Enclosure. The RDVB12 is a dual vented speaker box is made in the USA with Grade “A” ¾ MDF wood. This enclosure is made with precision cutting machinery by industry experts that have been making these enclosures in the USA for over 20 years. That means that the carpet will stay in place and not rip or tear. The ¾ USA MDF is much stronger then any type of import wood. This will keep your box performing at an optimal level by not flexing and distorting your woofers. Your woofers will thank you! EVERY Rockville enclosure is not only glued at all joints but stapled as well. If that wasn’t enough we add a layer of silicon to every seam! This makes your Rockville enclosure rock even more! MADE IN THE USA WITH PRIDE! Rockville RDVB12 Dual 12 1.75 cu. MDF Vented/Ported Subwoofer Enclosure Box. Dual 12 vented subwoofer enclosure. Machine precision cut mounting holes. 3/4 USA Heavy Duty MDF Construction. Top of the line Glue for extra durable adhesion. High quality GOLD spring loaded terminals. Designed, tested, and engineered to work with most of today’s popular woofers. These enclosures are built with the quality additives needed to maximize the performance of any sound system. Made in the USA. Type of Enclosure: Vented. Enclosure Sub Size: Dual 12. Dimensions in Inches: 16.75″ L x 36″ W x 13.25 H. Top and Bottom Depth: 19. Mounting Depth: up to 17.75 (enough depth for any sub on the market). Gross Volume Per Sub (Measurement for the outer dimensions of the box): 2.3 Cubic Feet. Net Volume Per Sub (Measurement for the outer dimensions of the box less the thickness of the wood): 1.75 Cubic Feet. Complete Dual Subwoofer Enclosure Installation Kit! This accessory package includes everything you need to install two subwoofers into an enclosure, and wire your enclosure to your amplifier. This package is a top of the line accessory package which we put together and tested. The drywall wood screws were hand selected by our installation experts because they drill into the enclosure very cleanly, without chipping the enclosure. The speaker wire is 14 gauge. This is way better than using 16 gauge. You can be 100 % sure that your enclosure will have a clean signal to the amplifier with this top of the line speaker wire. These spade terminals have also been hand selected by our installation experts to make the internal wiring simple, secure, and to run the audio signal cleanly. If your item is defective within the first 30 days of when it was delivered to you; you have the following options. We will send you a. To replace the item for a brand new one. If you want to return your item within the first 30 days of when it was delivered to you; you have the following options. This includes blown speakers with burned voice coils. Process for returning items. Item Code: (2) P3D2-12+DB15+RWK0CU+RDVB12+K2. The item “(2) Rockford Fosgate Punch P3D2-12 12 Subs+Vented Box+1500W Amplifier+Amp Kit” is in sale since Friday, June 23, 2017. This item is in the category “Consumer Electronics\Vehicle Electronics & GPS\Car Audio\Car Subwoofers”. The seller is “audiosavings” and is located in Inwood, New York. This item can be shipped to United States.
  • Brand: Rockford Fosgate
  • MPN: (2) P3D2-12+DB15+RWK0CU+RDVB12+K2
  • UPC: 613815937272
  • Type: Enclosed Powered
  • Model: (2) P3D2-12+DB15+RWK0CU+RDVB12+K2
  • Speaker Size: 12in.
  • Voice Coil: Dual
  • RMS Power: 600W
  • Country/Region of Manufacture: China
2 Rockford Fosgate Punch P3D2-12 12 1200W Car Subs+1500W RMS Amplifier+Amp Kit

2 Rockford Fosgate Punch P3D2-12 12 1200W Car Subs+1500W RMS Amplifier+Amp Kit

2 Rockford Fosgate Punch P3D2-12 12 1200W Car Subs+1500W RMS Amplifier+Amp Kit

2 Rockford Fosgate Punch P3D2-12 12 1200W Car Subs+1500W RMS Amplifier+Amp Kit

2 Rockford Fosgate Punch P3D2-12 12 1200W Car Subs+1500W RMS Amplifier+Amp Kit

2 Rockford Fosgate Punch P3D2-12 12 1200W Car Subs+1500W RMS Amplifier+Amp Kit

2 Rockford Fosgate Punch P3D2-12 12 1200W Car Subs+1500W RMS Amplifier+Amp Kit

2 Rockford Fosgate Punch P3D2-12 12 1200W Car Subs+1500W RMS Amplifier+Amp Kit

2 Rockford Fosgate Punch P3D2-12 12 1200W Car Subs+1500W RMS Amplifier+Amp Kit

2 Rockford Fosgate Punch P3D2-12 12 1200W Car Subs+1500W RMS Amplifier+Amp Kit

Car Audio & Video. Package: (2) Rockford Fosgate Punch P3D2-12 12 Dual 2 Ohm Car Subwoofers Totaling 2400 Watt Peak / 1200 Watt RMS + Rockville dB15 6000 Watt Peak 3000 Watt RMS Mono Class D Car Amplifier + Rockville RWK0CU 0 Gauge 100% Pure OFC Copper 2 Channel Complete Wire Kit With RCA Cables. Condition: BRAND NEW IN ORIGINAL PACKAGING. (2) Rockford Fosgate Punch P3D2-12 12 Dual 2 Ohm Car Subwoofers Totaling 2400 Watt. (1) Rockville dB15 6000 Watt/3000w RMS Mono Class D 2 Ohm Car Audio Amplifier. (1) Rockville RWK0CU 0 AWG Gauge Complete Amp Installation Wire Kit. Rockford Fosgate Punch P3D2-12 12 1200 Watt. Peak Power: 1200 Watts. RMS Power: 600 Watts. Nominal Impedance: Dual 2-Ohm. Anodized aluminum cone and dustcap. Custom 10-AWG nickel plated push terminals. Diamond cut cast aluminum trim ring. Dual linear spider with embedded 16 AWG tinsel leads. Extended pole piece and bumped vented backplate. High-temp voice coil with spun-laced Nomex® re-inforcement collar. Protective PVC textured magnet cover. StampCast basket with integrated spider venting. Cutout Diameter: 11.25 inches / (285 mm). Mounting Depth: 6.66 inches / (169.3 mm). Voice Coil Diameter: 2.5 / (65.5 mm). Magnet Weight 96 oz / 2.73 kg. Speaker Connector: Dual 10 AWG compression. Woofer Displacement: 0.194 cu. Ft / (5.5 Liters). Fs (Hz): 26.5. Re (Ohms): 3.20. Le (mH): 4.25. Vas (Liters): 57.7. Xmax (mm): 15.2. Vb: 1.02 cu. F3: 43.4 Hz. Speaker Cutout: 11.25 inches. Speaker Depth: 6.66 inches. Vd: 0.194 cu. Vb: 1.79 cu. F3: 33.2 Hz. Dp: 4 inches diameter. Lp: 10 inches long. Vp: 0.073 cu. Recommended Enclosure Type: ported or sealed. Minimum Sealed Box Volume: 0.50 cubic feet. Optimum Sealed Box Volume: 0.75 cubic feet. Maximum Sealed Box Volume: 0.85 cubic feet. Minimum Ported Box Volume: 0.70 cubic feet. Top-Mount Depth: 4.57. Cutout Diameter: 9.13. The dB15 is a class D monoblock high power amplifier with 6,000 watts peak output, 3,000 watts RMS output, and 1500 watts CEA-2006 rated power. All of the mono amplifiers in the dB series are 2 ohm stable. They are all CEA-2006 compliant, which makes it easy to compare this amplifier to other CEA compliant amps on the market. Here at Rockville we offer the best value in car audio. We therefore want to make it easy for you to compare our products to any brands on the market. So we provided 3 ratings for all of our car amplifiers. This peak power is the amount of power the amp puts out at the loudest moments during a particular song. This formula almost always works within 20 %. This amp has a fully adjustable 12dB/Octave crossover with differential circuitry. Other features include a subsonic filter, a fully adjustable bass equalizer, mute and delay soft start technology, a phase control switch, and a dashboard subwoofer control for added convenience. The dB15 is protected by a full IC controlled circuit and has professional peak limiter circuitry guaranteeing distortion free music playback at all levels. The RCA input accepts both balanced and un-balanced inputs. If there is potential inference in the car, the balanced input signal is less susceptible to noise. The dB amps by Rockville use the top parts and components recommended by Rockville’s very own engineer. These amps are the best sounding out of any series we have ever created. They perform more efficiently resulting in even dB of sound. We created them to be 2 ohm stable just like the world’s most famous amps by Rockford Fosgate, Kicker, etc. If you compare our amp to the most famous amps you will find our amp can compete and, in my opinion, surpass the performance of anything in its class. Each and every amplifier we manufacture is tested twice. Once at the semi-finished PCB stage of production, and then another test is done at the final assembly. We also run age tests on them. After this is all done, we hire a 3rd party independent company unaffiliated with our factory or with us to go to the factory and inspect 20% of all the production items. We test the power, the controls, and over 20 other tests. We guarantee these amps will satisfy you. (Amp must be complete along with the box). Birth sheet with tested power. Rockville dB156000 Watt/3000 Watt RMS Mono Class D 2 Ohm Car Stereo Amplifier With Optical Coupler Technology. CEA Compliant Power Ratings (Rated at less than 1 % distortion) Use these CEA ratings when matching and comparing with other CEA compliant brands such as Kicker, Rockford Fosgate, etc. O 2 Ohm: 1500 Watts x 1 Channel <1% THD+N o 4 Ohm: 900 Watts x 1 Channel <1% THD+N. RMS Power Ratings: Use these RMS ratings when comparing with great brands such as Hifonics, Earthquake, Soundstream, etc. O 2 Ohm: 3000 Watts x 1 Channel o 4 Ohm: 1800 Watts x 1 Channel. Peak: The amount of power the amplifier can produce for a split second at the loudest part of a song o 2 Ohm: 6000 Watts x 1 Channel o 4 Ohm: 3600 Watts x 1 Channel. High-Speed MOSFET Power Supply. Optical Coupler Class "D" Technology. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Low Pass Filter: 50Hz - 250Hz. Subsonic Filter: 15Hz - 55Hz. Full IC-Controlled Protection Circuitry. Remote Dashboard Subwoofer Control. Fully Adjustable 12dB Bass Equalizer. Mute and Delay Soft Start System. RCA Preamp Line Output. 8 Volt Preamp Circuitry. Status Mode LED Indicator. Minimum THD at Rated Power: <0.1%. S / N Ratio: >90dB. Under Voltage Protection at 10V. Over Voltage Protection at 16V. Frequency Response: 15Hz – 250Hz. 150 Amp Maxi Fuse. Dimensions: (W x H x L)9 x 2.4 x 17.8. About Rockville Quality Control Procedures. The Rockville brand stands for Quality, Innovation and Value. We aim to deliver products twice as good as our competitors at a fraction of the cost of famous brands. All Rockville products go through the most rigorous quality control standards in the industry. Products go through months of extensive testing before they reach your hands. All functions and components are tested for quality. Rockville makes products that are virtually un-breakable! Rockville is one of the only brands in its class to have engineers and technicians test every concept model for weeks or months before starting production. Once production begins, Rockville sends product engineers to the factory to quality control every product. After production is complete Rockville has the head of QC in our overseas office test a certain percentage of all products from the production line a second time to ensure that the quality meets our strict standards. We challenge anyone to put this wire to a resistance test against any other wire on the market with the same gauge. Why are we so confident? This cable is 100% copper. You cant have a cable with more copper than 100 %. So the only way a cable would out-perform this one is if it were being advertised as a 0 AWG but they are giving you more wire than advertised. We guarantee that this kit will compete with the most expensive amp kits on the market from Kicker, JL Audio, or any other top brands. Looking for a wire kit that has 100% true specifications? A wire kit that uses 100% copper 0 gauge cable? Then look no further than the Rockville True-Spec RWK0-CU 0 Gauge Amplifier Wiring Installation Kit. This package includes everything you’ll need to get your amplifier system powered-up correctly and at peak efficiency. The power and ground cables aptly named “Mega Power Cable” are a no compromise power cable. Rockville’s engineering team over-built and designed the cables using thousands of strands of only true 100% oxygen-free, silver-tinned copper strands. The use of a proprietary special twisting process reduces “surface skin impedance loss” so that Mega Power cables have zero signal and power loss, delivering full power from your battery system to your amplifier even at lengths of 20 feet! The increased current flow and higher amperage carrying capacity will increase your amplifiers efficiency and keep your amplifier running cooler. The SuperFlex outer insulating jacket jacket makes installation and cable routing simple and easy. The 100% copper stranded wire is extremely tolerant of the hostile conditions found under the hood in vehicles and compensates for vibration, heat expansion and flexibility. This flexible and well shielded wire is crucial for getting through all of the nooks and passageways within the confines of a vehicle interior. Some manufactures use all aluminum or mix a little copper with aluminum to give their cables the appearance of a “heavy-duty” cable. But not Rockville, our True-Spec 100% oxygen free, silver tinned copper eliminates corrosion, increases current transfer x 10, and won’t discolor over time. The superior quality and materials of the Rockville 100% True-Spec amplifier installation kit is realized in the included accessories and cable workmanship. Included is a precision CNC cut full size ANL fuse housing, machined from solid brass and then 14K gold plated for superior signal transfer and complete with a matching gold plated 250-amp ANL fuse. The power cable is wrapped in 6 feet of durable nylon braided tubing to protect it from heat and chafing in the engine compartment. All installation accessories such as the ring terminals and spade connectors are nickel plated for superior signal transfer and durability. CRYSTAL SQ AUDIO PLANAR SPEAKER CABLE The speaker cable included in the Rockville True-Spec is also manufactured from 100% copper and woven in to a flat planner design and coated in our Super-Flex insulation so that it fits under and around your vehicles trim and carpet smoothly and without bulking up. With crystal clear sound quality these speaker cables deliver true audio fidelity from your car audio amplifier to your speakers. The 12 gauge speaker cable included in the 0 gauge kit can handle over 3000 watts of power without heating up or degrading signal quality. CRYSTAL SQ RCA AUDIO INTERCONNECT CABLE Designed and engineered to be the best sounding, best performing and best looking RCA cables available today. Each channel in the RCA cable is triple shielded first with dielectric internal insulators and then with a 98% coverage woven shield. All cables are manufactured of 100% oxygen free copper and feature twisted pair technology for superior noise rejection and pure sonic signal flow. The RCA plugs are shielded metal and feature a spiral cut outer ground ring with center split pin for precise and tight audio connections. The result of all this technology is noise free-noise rejection signal transfer for optimum sound quality. You will hear the difference these RCA signal transfer cables will make. Amplifier Kit Key Features. 0 Gauge Power Amplifier Installation Kit. Designed specifically for car audio systems over 1000 watts RMS to 3000 Watts. Made from silver-tinned 100% virgin copper for a pure uninterrupted transfer of power and signal. The solid brass gold plated ANL Fuse Holder offers ideal protection for high powered systems. Frosted Blue 0 gauge power wire with seamless crimp ring terminal. Frosted Gray 0 gauge ground wire. Blue 18 gauge remote lead wire. Frosted Clear/Blue 12 gauge flat speaker wire. Triple shielded twisted pair RCA cables. One ANL Fuse Holder with 250 amp ANL fuse. One 1/2 black rubber firewall grommet. Two 0 gauge spade terminals. Two black 12 gauge nickel-plated spade lugs. Three blue 12 gauge nickel-plated spade lugs. One black 0 gauge ring terminal. Ten 6 black zip ties. If your item is defective within the first 30 days of when it was delivered to you; you have the following options. We will send you a. To replace the item for a brand new one. If you want to return your item within the first 30 days of when it was delivered to you; you have the following options. This includes blown speakers with burned voice coils. Process for returning items. Item Code: (2) P3D2-12+DB15+RWK0CU. The item “2 Rockford Fosgate Punch P3D2-12 12 1200W Car Subs+1500W RMS Amplifier+Amp Kit” is in sale since Friday, June 23, 2017. This item is in the category “Consumer Electronics\Vehicle Electronics & GPS\Car Audio\Car Subwoofers”. The seller is “audiosavings” and is located in Inwood, New York. This item can be shipped to United States, Canada, United Kingdom, Mexico, Germany, Japan, Brazil, France, Australia, Russian federation, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Greece, Portugal, Cyprus, Slovenia, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Austria, Israel, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica.
  • Brand: Rockford Fosgate
  • MPN: (2) P3D2-12+DB15+RWK0CU
  • UPC: 613815937258
  • Type: Non-Enclosed Powered
  • Model: (2) P3D2-12+DB15+RWK0CU
  • Speaker Size: 12in.
  • Voice Coil: Dual
  • RMS Power: 600W
  • Country/Region of Manufacture: China